How to Pick the Right Case for Your Tiny Whoop (Mobula, Meteor, Pavo and More)

Your drone survives crashes. Your gear bag is another story.

If you fly tiny whoops, you already know the routine: the whoop goes in a pocket, the batteries rattle around in a baggie, the spare props end up at the bottom of your backpack, and the little USB charger is gone forever. Tiny whoops are tough in the air. It's the transport that chews them up - bent props, popped canopies, lost screws, a stripped motor lead from getting crushed under a water bottle.

A case fixes that. But not just any case. A generic foam box that "kind of" fits leaves your drone sliding around, and a case built for a 5-inch freestyle rig is way too big for a 65mm whoop. What you actually want is a case shaped for your drone.

What makes a good tiny whoop case

A few things separate a case you'll actually use from one that lives in a drawer:

• A fitted pocket for your specific model. Your drone shouldn't move. A snug cradle means no rattling, no pressure on the props, no cracked canopy.
• Battery organization. This is the big one for whoop pilots. You carry a lot of 1S and 2S packs. A case that slots them in neatly beats a loose pile every time.
• Room for the little stuff. Spare props, a USB adapter, screws, your goggles strap. The parts that vanish.
• A material that takes a hit. Foam crushes. Thin plastic cracks in the cold. You want something with a little give that bounces back.

Find your case

We design these cases around one drone each, so the fit is exact - not "close enough." Here's the current lineup:

• Happymodel Mobula 6 Case - Built for the 2024 Mobula 6. Clamshell with organized slots for a stack of spare 1S packs.
• Happymodel Mobula 8 Case - Fits the Mobula 8 and keeps your 2S packs, a USB adapter, and accessories in order.
• BetaFPV Meteor 65 Pro Case - For the Meteor65 Pro, with slots for your 1S Lava cells.
• BetaFPV Air65 and Air65 II Case - For the Air65 II in Champion, Racing or Freestyle trim, and the original Air65. Our smallest case.
• BetaFPV Meteor 75 Pro Case - For the Meteor75 Pro, with room for a full stack of 1S batteries.
• BetaFPV Meteor75 and Air75 Case - One case sized for both the Meteor75 and the Air75, plus your 1S packs.
• BetaFPV Meteor75 Pro II Case - For the second-gen Pro II with the O4 Lite or O4 Wide. It does not fit the original Meteor75 Pro, so check which one you fly.
• BetaFPV Meteor75 Pro + WhoopStor V3 Case - Fits the Meteor75 Pro or Pro II and adds a bay for a WhoopStor V3 charger, so your drone, twelve 1S packs, and the charger all travel in one box.
BetaFPV Pavo20 Pro and Pro II Case - Updated design. Fits the Pavo20 Pro II with the O4 Pro, O4 Lite or O4 Wide canopy, plus the first-gen Pavo20 Pro. Holds 3S and 4S Lava packs.

Cases start at $29.99, with a few size and color options on each listing.

Why we print these in PETG

We print every case in PETG, not the cheaper PLA you'll see on a lot of marketplace listings. The reason is simple: PETG handles heat and impact far better. A PLA case left on a car dashboard on a Texas afternoon can soften and warp. PETG shrugs it off, and it flexes under impact instead of snapping. For something that lives in a hot car or a packed bag, that difference matters.

Each case uses an integrated print-in-place hinge - a piece of filament acts as the pin, so there's no extra hardware to lose and nothing to wear out. It's a small detail that makes the whole thing more reliable.

Don't see your drone?

We add new models as pilots ask for them, and we build custom one-offs too. If you fly something that isn't on the list, browse all of our 3D printed FPV drone cases or send us a message with your exact model and battery setup. If we can get our hands on the specs, we can usually make it fit.

Fly more, fix less. Get your drone in a case that was actually made for it.